Learning the Basics of Plumbing for Bathtub Installation
Learning the Basics of Plumbing for Bathtub Installation
Blog Article
What are your opinions with regards to How to Install a Bathtub?
Installing a bathtub isn't precisely rocket science, yet it does require solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably challenging project. If the old tub is easily easily accessible, the job can move immediately; if you have to open a wall to remove the old bathtub as well as position the brand-new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make certain you have certified yourself for the task and are comfortable trying it. As opposed to hiring a specialist to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Chances are you might require a specialist plumber to make tube links.
This post will aid you install a new tub in your restroom if you have currently bought a new bathtub and also do not require to transform the setup of your previous supply of water pipes.
Your tools and material checklist ought to comprise the following:
Preparing for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to prevent pressure on the tub.
Fit the versatile faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing taps can be quite troublesome due to the restricted access that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bathtub in the required placement. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to ensure that the tub is leveled all round. This can be attained by examining the level and adjusting the feet on the tub up until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply and inspect all joints and also new pipework for leaks as well as tighten them if essential. Load the tub as well as likewise check the overflow electrical outlet and also the normal electrical outlet for leaks.
Lastly, fix the bath paneling as described in the maker's user's manual. Tiling as well as sealing around the tub should wait up until the tub has actually been used at the very least once as this will resolve it into its last position.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the manufacturer given backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The previous type should be linked to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture an inflexible seal, causing the water to pass through the wall surface in between the bath and also the tiling, leading to complications with wetness and possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your fixtures as well as fittings. They are sold in tubes and cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealer can split rather early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a person who reads about Tools You Need to Install a New Bathtub , I figured sharing that article post was really useful. Do you know somebody else who is occupied with the niche? Do not hesitate to share it. Kudos for your time. Please come visit our blog back soon.
For instant fixes, dial! Report this page